搡多毛BBBB╳╳乂乂H,国产精品久久久久久一级毛片,男女无遮挡XX00动态图120秒,香蕉视频在线播放

Current location:Home > News > News detail

Analysis and troubleshooting of common faults in sanding machines

Date: 2023/8/3

During the operation of the machine, some faults often occur, but they should be eliminated in a timely manner. However, if not handled properly, it may affect production and increase costs. This requires operators to be familiar with operating procedures, proficient in operation, and timely troubleshooting. Some faults were not found to be serious, but if handled improperly, they can cause significant malfunctions and seriously affect production. The following is an analysis of common faults in sanding machines.
1. Belt deviation is generally caused by improper adjustment. The normal swing amplitude of the sand belt should be 15-20 millimeters, and the swing frequency should be 15-20 times/minute. The swing speed should be moderate and consistent. If in an abnormal state, there may be deviation over time, especially if the swing speed is inconsistent, which is more likely to cause abnormal shutdown; The photoelectric switch is damaged, the solenoid valve is damaged, and the oscillating cylinder is damaged. The dust collection is not good. High dust concentration will affect the normal operation of Phototube, and will also lead to the deviation of abrasive belt. Replace damaged accessories in time to improve the dust removal effect.
2. The limit switch is malfunctioning, and both sides of the sand belt have limit switches. When the sand belt fails to swing and deviates to one side, it touches the limit switch, releases the sand belt, and the main motor automatically stops, effectively protecting the sand belt. Once the limit fails, the sand belt will be damaged, and the friction frame will generate sparks or even fire. Therefore, limit switches should be regularly checked for stable operation.
3. The sand belt is wrinkled, and once it is wrinkled, it cannot be used again. There are generally three possible causes of sand belt wrinkling: wear of sand roller and tension roller, grinding method, and repair roller; The sand belt is damp, soft, and wrinkled, and can be treated by drying and drying; The sanding machine has been unused for a long time, and the surface of the sanding roller is rusted and rough, making it difficult for the sanding belt to swing, resulting in a starting trend. At this point, a roller should be used for rust removal or a finer sandpaper should be used for polishing.
4. Sand belt fracture and sand belt fracture are mainly caused by sand belt deviation, blunt grinding of sand belt without timely replacement, excessive load of sand belt, or encountering hard objects or quality problems during the grinding process. Try to avoid sand belt breakage, otherwise it may cause a fire. When the current is abnormal, it is necessary to observe whether the sand belt is worn dull. If so, it should be replaced in a timely manner.
5. Deviation, slipping, rebound when entering the board. In the adjustment of the sanding machine, it is required to adjust the back pressure spring of the upper conveying roller to two-thirds (the remaining one-third). The spacing between the upper and lower conveying rollers should be less than 1.5mm or 1mm of the thickness of the passing slab, otherwise it may cause the slab to deviate or slip. In severe cases, it can cause rebound and may harm personal safety.
6. After replacing the sanding belt, the size of the sanding board changes. When the locking block is loosened or locked, the cantilever position of the sanding machine fluctuates greatly, which should be within 0.5mm under normal circumstances. If it is too large, the difference in locking force when the locking block locks the cantilever will cause different repetition accuracy of the cantilever, leading to fluctuations in the size of the sanding plate, which directly affects the sanding accuracy of the sanding machine. When the cantilever error is too large (exceeding 0.5) mm), the fixing bolts of the locking block should be adjusted appropriately. At the same time, when replacing the sand belt, the locking strength of the locking block should be consistent.
7. When the car is empty, the conveying roller rotates intermittently or does not rotate, and the above situation cannot be observed generally. It can only be found when the car is empty, because the worm gear is partially or completely worn

成人黄色A片视频在线观看 精品国产九九乱伦AV电影 | 久久久久久久久久91 | 99国产精品久久久久久久成人 | 亚洲精品国产精品国自产 | 91丨国产丨白浆秘 喷水 | 色久欧美视频在线观看 | 精精国产XXXX视频在线播放 | 渐江妇搡BBBB搡BBBB | 欧美日韩精品在线观看 | 亚洲二区三区精品 | 特级毛片片A片AAAAAA | 欧美大黑BBBBBBBBB在线播放 | 日本成人一区二区三区 | 精品中文一区二区 | 欧美午夜精品一区二区蜜桃 | 真人一级毛片免费看在线 | 少妇与大狼拘作爱一级A片入口 | 日本又粗又大淫秽视频 | 黑人 娇小 亚洲 硬 欧美成人免费高清视频 | 四川少妇BBBBBB爽爽小说 | 免费无码婬片17com | 国产精品日韩一区 | 婷婷社区伊人在线 | 中文字幕亚洲精品影院 | 欧美 日韩 中文字幕 | 欧美日本三级片免费看 | 91麻豆精品无码人妻系列熟人 | 福利柠檬成人AⅤ导航 | 西西人体大胆4444ww无视频 | 日本美女在线播放 | 91丨国产丨白浆秘 喷淫 | 99精品国产免费无码 | 真实国产乱子伦精品一区二区三区在线观看 | 成人国产AV无码一区二区 | 1v1H潮喷在线免费观看 | 大乳奶一级婬片A片无码 | 四lllBBBB槡BBBB | 久久99久久精品 | 精品少妇人妻Av免费久久三叶草 | 成人无码做爰毛片国产 | 天天婬欲婬香婬色婬 |